Epson Encoder

Description

Epson Encoder

epson encoder

This Epson Encoder is for the following printers: Epson 24 inch printers 4880 7800 7890 7700 7900 Epson 44 inch printers 7000 9890 9900 9800 Epson 36 inch printers SC T5000

Epson Printer Encoder Strip 64

This Epson Printer Encoder Strip is for the following printers: Epson 64 inch printers SC70600 SC50600 SC30600

Epson Printer Encoder Strip 11880

This Epson Printer Encoder Strip is for the following printers: Epson 11880

Epson Printer Encoder Strip 24

This Epson Printer Encoder Strip is for the following printers: Epson 24 inch printers 4880 7800 7890 7700 7900 F2000 T3270

Epson Encoder Strip 36

This Epson Encoder is for the following printers: Epson 36 inch printers SC T5000 T5270 T5270D

Epson Encoder Strip 44

This Epson Encoder is for the following printers: Epson 44 inch printers 7000 9890 9900 9800 T7270 T7270D F6070

Epson Encoder Strip 7880

This Epson 7880 Encoder Strip is the same width as Epson OEM Encoder Strip.
This Epson Encoder is for the following printers: Epson 44 inch printers 7880 7000 9890 9900 9800 T7270 T7270D F6070

Epson Printer Encoder Strip 64

This Epson Printer Encoder Strip is for the following printers: Epson 64 inch printers 11880 SC70600 SC50600 SC30600 S30675 S50675 S70675

Epson Printer Encoder Strip

How to clean Epson Printer Encoder Strip Strip?
You will need Isopropyl Alcohol, Cleaning Swabs and Paper Towels.
Putting two drops of alcohol onto each side of the cleaning swab. Dab the swab on the paper towel to soak up any excess liquid.
Wipe the exposed area of the Epson Printer Encoder Strip strip gently in one direction, do not try to scrub the strip or bend it. Repeat the cleaning for the back of the Epson Printer Encoder Strip strip.
Put the machine into Cleaning Mode under the Maintenance Sub-Menu. You will now be asked to remove the maintenance cover on the left side of the printer.
After the Head Carriage moves to the left side of the printer, continue to clean the area of the Epson Printer Encoder Strip strip that is now exposed over the docking area.
Once the Epson Printer Encoder Strip strip has been cleaned, perform a Limit Initialization to reset the Head Carriage.
All printer manufacturers use optical Epson Printer Encoder Strip strips in inkjet printers to tell the print head carrier how for it has moved and also when it return to home position. If you get a bad printer jam hat blocks the carrier this Epson Printer Encoder Strip strip can get disconnected and then the printer can not print anything. We are about to show you how to repair the strip if it is damaged and reinstall it so the printer can function again. This guide uses the Roalnd Printer as an example but the steps are the same for any printer that uses these Epson Printer Encoder Strip strips. The first thing to do is check the strip for damage. Check both ends and make sure the plastic is not torn. The ends should have an opening about 1/4 inch from the end as seen here.
If your Epson Printer Encoder Strip strip is torn you can usually repair it with packing tape. Wrap the tape around the end several times and the use a small knife to cut the tape where the original hole was as seen below. Then cut the tape off the strip around the side and end.
Now its time to reinstall the strip. The Epson Printer Encoder Strip strip attaches to retainer brackets and both sides of the printer and is threaded through the printhead carrier in the middle. You will need the carrier to be in the middle of the printer. To get it there you will need to power up the printer and open the cover like you were going to change the print heads. Power up the printer and the print heads should start to move to the side. When they get about the center of the printer you will need to pull the power plug so they stop moving. Connect one end of the Epson Printer Encoder Strip strip as seen here.
Now thread the Epson Printer Encoder Strip strip through the carrier as seen here. The outside opening is about 1/2 inch but the slot the encoder goes in is only about 1/16in so be patient.
Then connect the other end of the Epson Printer Encoder Strip strip, the left hard side is spring metal to tension the strip and keep it tight.
Now if you reapply the power to the printer the carrier should move freely and move back to the right side. Close the printer cover and try a test print to see if it work. If you still get a carrier jam then the strip did not get inserted correctly through the carrier. Just disconnect it and try again.
epson encoder strip for all epson printers
epson encoder 11880 SC70600 SC50600 SC30600 S30675 S50675 S70675 SC70600 SC50600 SC30600 SC T5000 4880 7800 7890 7700 7900 7000 9890 9900 9800

Epson Printer Encoder Strip

epson encoder strip for all epson printers 100% compatible replacement
epson encoder 11880 SC70600 SC50600 SC30600 S30675 S50675 S70675 SC70600 SC50600 SC30600 SC T5000 4880 7800 7880 7890 7700 7900 7000 9890 9900 9800